Genelec G Three 2-Way Active Loudspeaker (Polar White)(Genelec G Three 2 Way Active Loudspeaker Polar White 2)

The polar white G Three 2-Way Active Loudspeaker from Genelec is designed to produce broad bandwidth sound with high output and low coloration. The reflex port design helps in reducing the woofer�s displacement, improving the linear low frequency output capacity.

Audio input is via a 10 kOhm balanced female XLR connector or unbalanced RCA connector. Only line level audio signal from a preamplifier, computer sound card, or similar signal source can be connected. It is possible to connect two audio sources to the loudspeakers at the same time using both connectors, as long as only one source is used at a time. The playback level of the loudspeakers has two basic settings, normal and -10 dB. Bass and tone controls allow you to further customize or adjust the sound based on room placement.

The Iso-Pod (Isolation Positioner/Decoupler) vibration insulating table stand allows tilting the loudspeaker for correct vertical alignment. There are 3 mounting points for the Iso-Pod on the back of the loudspeaker cabinet allowing vertical and symmetrical horizontal positioning. On the base of the loudspeaker is a 3/8� UNC threaded hole compatible with a standard microphone stand. On the rear there are two sets of threaded holes for Omnimount and König & Meyer brackets.

The signal sensing Autostart function of the loudspeakers powers them up when playback begins. Automatic powering down of the loudspeakers happens one hour after the playback has ended and the loudspeakers go to standby mode. The power consumption in standby mode is less than 0.5W. The loudspeaker will automatically and rapidly start once an input signal is detected from the source.

Technologies

Directivity Control Waveguide (DCW)

Optimized amplifiers

Active crossovers

Room response compensation

Protection circuitry

Minimum Diffraction Enclosure (MDE)

Reflex port design

Intelligent signal sensing

Genelec G Three 2-Way Active Loudspeaker (Polar White)

SPL	104 dB
Frequency Response	47 Hz to 25 kHz (-3 dB) Accuracy: ± 2.5 dB (54 Hz to 20 kHz)
Driver	Woofer: 5″ / 127 mm Tweeter: 0.75″ / 19.5 mm metal dome
Amplifier Power	Woofer 50 W + Tweeter 50 W
Connections	1 x RCA analog input 1 x XLR analog input
Crossover	Input Impedance: 10 kOhm Crossover frequency, Bass/Treble: 3 kHz Treble Control Operating Range in 2 dB Steps: -2 dB @ 15 kHz Tabletop Low Frequency Control Operating Range: -4 dB @ 200 Hz Low Bass Control Operating Range: 4 dB @ 55 Hz Bass Control Operating Range in 2 dB Steps: From 0 to -6 dB @ 100 Hz
Amplifier	Bass/Treble Amplifier Short Term Output Power: 50 W each Amplifier System Distortion at Nominal Output (THD/SMPTE-IM/CCIF-IM/DIM 100): ?0.05 % Signal to Noise Ratio, Referred to Full Output (Bass/Treble): ?100 dB Mains Voltage: 100-240 VAC, 50/60 Hz, ±10% Power Consumption: <0.5 W (standby), 10 W (idle), 80 W (full output)
Dimensions	Height (Without Table Support): 11.81″(300 mm) Height (Including Table Support): 11.25″(285 mm) Width: 7.43″(189 mm) Depth: 7″ (178 mm)
Weight	11.2 lb (5.1 kg)

Packaging Info
Package Weight	15.7 lb
Box Dimensions (LxWxH)	17.4 x 11.8 x 11.7″